10-Pin TC2050 family

TC2050-MINIHDMI-NL "No Legs" Cable for Altium's USB JTAG programmer

TC2050-MiniHDMI-NL Cable for Altium's USB JTAG Programmer Tag-Connect TC2050-MiniHDMI cable with Altium's USB JTAG Programmer

TC2050-MINIHDMIThe TC2050-MINIHDMI and the TC2050-MINIHDMI-NL are 10 pin Plug of Nails Cables for use with Altium's cross platform USB JTag unit which uses a Mini-HDMI connector.  

Refer to the TC2050-IDC and TC2050-IDC-NL Datasheets for TC2050 Footprint Details.  

Product information can be read here.

Alitium discontinued their USB JTag programmer several years ago. This is the last batch of these MINIHDMI cables, we do not plan to make more (but can always make a special cable for you). You can always use our standard TC2050-IDC and TC2050-IDC-NL cables with one of Altium's adapters.

$39.95

TC2050-MINIHDMI Legged Cable for Altium's cross-platform USB JTAG programmer

TC2050-MINIHDMIThe TC2050-MINIHDMI and the TC2050-MINIHDMI-NL are 10 pin Plug of Nails Cables for use with Altium's cross platform USB JTag unit.  

Refer to the TC2050-IDC and TC2050-IDC-NL Datasheets for TC2050 Footprint Details.  

Product information can be read here.

Discontinued. Alitium discontinued their USB JTag programmer several years ago. We do not plan to make more of this cable (though can always make a special cable for you). The TC2050-MINIHDMI-NL version may still be available.

$39.95

TC2050-IDC-NL-430 No Leg Cable for use with MSP430 / FET430

Tag-Connect’s TC2050-IDC-430-NL cable is a special version of the TC2050-IDC-NL Plug-of-Nails™ cable designed to be plugged directly into TI’s MSP-FET430 and is compatible with all MSP430 MCU’s. The cable is fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 14-pin 0.1” ribbon connector that plugs directly into the FET430.

 

The cable is fitted with a spring-pin Tag-Connector.

Plugs straight to your PCB - No mating connector or header required!

Requires only a tiny 0.03 square inch footprint of pads and locating holes in your PCB.

Footprint MUCH smaller than the standard 14-pin ribbon header.

Zero Cost Per Board!

High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.

Footprint has no height and reduces the size and space requirements of your PCB.

Can be retained in place using a TC2050-CLIP board.

 

Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB’s while lowering board costs and facilitating efficient production programming.

Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.

The legged “No Legs” footprint takes about the same board space as a couple of SMT resistors which means you can locate the footprint right next to the MCU if desired. If required, use the TC2050-CLIP board to secure the TC2050-IDC-430-NL connector to the PCB.

The “No Legs” Tag-Connector is also compatible with the “Legged” footprint, meaning you can conveniently debug with the self-retaining TC2050-IDC-430 and use TC2050-IDC-430-NL for a quick hand-held programming operation as may be typical during production.

This 10-conductor cable has a TC2050 Tag-Connector on one end and a standard 14-pin ribbon connector on the other and is wired specifically for the TI MSP-FET430 debugger (and compatible MSP430 debuggers). It is compatible with all MSP430 MCU’s.

If your MSP430 device supports SPY-BI-WIRE, also take a look at the SPY-BI-TAG adaptor with the even smaller footprint (0.02 square inches) TC2030-MCP-NL 6-pin cables. This is the perfect solution where board space is premium!

 

For full specifications, please download the TC2050-IDC-NL-430 Datasheet (pdf)


Also available in self-retaining “legged” version (TC2050-IDC-430). See TC2050-IDC-430

This product is available from our distributors

$43.00

TC2050-IDC-430 Legged Cable for use with MSP430 / FET430

Tag-Connect’s TC2050-IDC-430 cable is a special version of the TC2050-IDC Plug-of-Nails™ cable designed to be plugged directly into TI’s MSP-FET430 and is compatible with all MSP430 MCU’s.

 

The cable is fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 14-pin 0.1” ribbon connector.

Plugs straight to your PCB - No mating connector or header required!

Requires only a tiny footprint of pads and locating holes in your PCB.

Footprint MUCH smaller than the standard 14-pin ribbon header.

Zero Cost Per Board!

High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.

Footprint has no height and reduces the size and space requirements of your PCB.

 

Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB’s while lowering board costs and facilitating efficient production programming.

Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.

The legged version footprint takes about the same board space as two or three SMT resistors which means you can locate the footprint right next to the MCU if desired.

This 10-conductor cable has a TC2050 Tag-Connector on one end and a standard 14-pin ribbon connector on the other and is wired specifically for the TI MSP-FET430 debugger (and compatible MSP430 debuggers). It is compatible with all MSP430 MCU’s.

See also TC2050-IDC-NL-430 (no-legs version) with a tiny 0.03” footprint. Also, if your MSP430 device supports SPY-BI-WIRE, take a look at the SPY-BI-TAG adaptor with the even smaller footprint TC2030-MCP 6-pin cables.

For full specifications, please download the TC2050-IDC-430 Datasheet (pdf)


Also available in space-saving “no-legs” version. See TC2050-IDC-NL-430

This product is available from our distributors

$43.00

TC2050-IDC-NL 10-Pin No-Legs Cable with Ribbon connector.

Tag-Connect’s TC2050-IDC-NL “No Legs” Plug-of-Nails™ cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1” ribbon connector.

 

Plugs straight to your PCB - No mating connector or header required!

Requires only a tiny 0.03” footprint of pads and locating holes in your PCB.

Zero Cost Per Board!

Tiny Footprint!

High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations

Footprint has no height and can reduce the size and space requirements of your PCB.

A great way to make test and debug signals available at no cost and with minimal board space.

Can be retained in place using a TC2050-CLIP board.

Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB’s while lowering board costs and facilitating efficient production programming.

Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.

The tiny “No Legs” footprint takes only 0.03 square inches (about the same board space as a couple of SMT resistors) which means you can locate the footprint right next to the MCU if desired.

This 10-conductor cable has a TC2050-NL Tag-Connector on one end and a standard 0.1” ribbon connector on the other and is suitable for use with most many MCU’s / FPGA’s and JTAG programming and debug operations.

A growing range of adaptors are available for specific and generic applications such as Xilinx SPARTAN and VERTEX FPGA’s, TI MSP430 (TC2050-IDC-430), etc

For full specifications, please download the TC2050-IDC-NL Datasheet (pdf)

Also available in self-retaining “legged” version (TC2050-IDC). See TC2050-IDC

This product is available from our distributors

$39.00

TC2050-IDC - Tag Connect 2050 IDC

Tag-Connect’s TC2050-IDC Plug-of-Nails™ cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1” ribbon connector.

 

Plugs straight to your PCB - No mating connector or header required!

Requires only a tiny footprint of pads and locating holes in your PCB.

Zero Cost Per Board!

Tiny Footprint!

High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations

Footprint has no height and can reduce the size and space requirements of your PCB.

A great way to make test and debug signals available at no cost and with minimal board space.

 

Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB’s while lowering board costs and facilitating efficient production programming.

Tag-Connect uses a patented specially designed connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.

The legged version footprint takes about the same board space as two or three SMT resistors which means you can locate the footprint right next to the MCU if desired.

This 10-conductor cable has a TC2050 Tag-Connector on one end and a standard 0.1” ribbon connector on the other and is suitable for use with most many MCU’s / FPGA’s and JTAG programming and debug operations.

A growing range of adaptor cables are available for use with various applications, such as ARM MCU's, Xilinx SPARTAN and VERTEX FPGA’s, TI MSP430 (TC2050-IDC-430) and Renesas MCU's compatible with E1/E8a debuggers.

For full specifications, please download the TC2050-IDC Datasheet (pdf)

See also TC2050-IDC-NL (no-legs) version with a tiny 0.03” footprint

This product is available from our distributors

$39.00