Tag-Connect™ Solutions for Microchip PIC32 MIPS MCUs
Please see below for a list of Tag-Connect™ small footprint debugging/programming cable solutions for Microchip PIC32 MIPS MCUs. Solutions may be available for different sized target board connectors, different debugging/programming protocols or different debuggers. Solutions are also available for either “legged” or “no legs” versions of the plug-of-nails™ target board connectors. Use the debugger links to see further information on these options as applicable to particular debuggers.
RJ12 to 6 Pin Plug-of-Nails™ - No Legs (10" cable) Debugger mating connector: 6 Pin RJ11/RJ12
This is the 10"/254mm (longer) version of the TC2030-MCP-NL programming cable.
Note that 10" exceeds the Microchip maximum?cable length specification of 8" and is not supported by Microchip. However, the additional length provides increased convenience and has not been known to cause problems in general use.
Microchip to date has only specified the maximum length of the programming cable and not the typical additional length of PCB traces needed between the RJ12 connector (which might be on the edge of the PCB) and the MCU. With the much smaller TC2030 footprint you can usually put the ICD connection right at the MCU.
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
RJ12 to 6 Pin Plug-of-Nails™ - No Legs (standard cable) Debugger mating connector: 6 Pin RJ11/RJ12
Tag-Connect TC2030-MCP-NL programming cable is primarily intended for use in production programming. It is particularly suited to environments where the connection to the PCB is of short duration, and operators are working quickly from board to board.
A major advantage of the TC2030-MCP-NL is the extremely small footprint required on the PCB (hardly any bigger than a surface mount resistor) allowing the minimum possible space on your PCB to be used for the programming connection.
The TC2030-MCP-NL is also compatible with the TC2030-MCP footprint allowing use of the TC2030-MCP for development work and TC2030-MCP-NL for fast programming in production.
The TC2030-MCP-NL can be held in place making it suitable for debugging and development when using TC2030-CLIP board .
Where a sustained connection to the PCB is required, also consider the TC2030-MCP.
Ideal for efficient production programming and also for debugging.
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
RJ12 to 6 Pin Plug-of-Nails™ - With Legs (10" cable) Debugger mating connector: 6 Pin RJ11/RJ12
This is the 10" (254mm) (longer) version of the TC2030-MCP programming cable.
Note that 10" exceeds the Microchip maximum cable length specification of 8" and is not supported by Microchip. However, the additional length provides increased convenience and has not been known to cause problems in general use.
Microchip to date has only specified the maximum length of the programming cable and not the typical additional length of PCB traces needed between the RJ12 connector (which might be on the edge of the PCB) and the MCU. With the much smaller TC2030 footprint you can usually put the ICD connection right at the MCU.
RJ12 to 6 Pin Plug-of-Nails™ - With Legs (standard cable) Debugger mating connector: 6 Pin RJ11/RJ12
Tag-Connect TC2030-MCP cable is primarily intended for use in development environments and is also ideal for production programming. The spring-loaded contact pins are held firmly in place by four plastic legs each of which clips securely into its own locating hole.
Tag-Connect TC2030-MCP is ideal where you need to maintain a connection to the PCB for an extended period such as when performing testing or development work.
See also TC2030-MCP-NL for applications where an even smaller footprint is required.
Ideal for both debugging and production programming.
This special cable has a 6-pin ECV3-06 Edge-Connect™ connector and an RJ12 Modular Plug for Microchip ICD.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
Edge-Connect™ is the patent-pending newest member in the family of Programming Connectors and Cables from Tag-Connect. ECV3-06 is the 6-pin connector.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
ECV3-06-MCP has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
New datasheet coming soon. Note that this product terminates in an RJ12 connector.
Note: ECV3-06-MCP with ribbon cable and RJ12 connector only supplied, Demo PCB not included.
PICkit to 6 Pin Plug-of-Nails™ - No Legs (PIC) Debugger mating connector: 6 Pin 0.1" SIP strip Male
For PICkit3, PICkit4 and PICkit5.
Tag-Connect TC2030-PKT-NL cable is primarily intended for use in production programming. It is particularly suited to environments where the connection to the PCB is of short duration, and operators are working quickly from board to board.
A major advantage of the TC2030-PKT-NL is the extremely small footprint required on the PCB (hardly any bigger than a surface mount resistor) allowing the minimum possible space on your PCB to be used for the programming connection.
The TC2030-PKT-NL (no legs) cable is also compatible with the TC2030 legged footprint allowing use of the TC2030-PKT legged cable for development work and TC2030-PKT-NL for fast programming in production.
The TC2030-PKT-NL is also suited to use for debugging and development when secured into position using a TC2030-CLIP board. See 'Using the TC2030-MCP-NL for debugging' on the User Information page for details.
Where a sustained connection to the PCB is required, also consider the TC2030-PKT.
Ideal for both debugging and production programming, the 6 pin plug-of-nails™ cable terminates in a 6 pin 0.1" male SIP strip.
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
PICkit to 6 Pin Plug-of-Nails™ - With Legs (PIC) Debugger mating connector: 6 Pin 0.1" SIP strip Male
For PICkit 3, PICkit4 and PICkit5.
Tag-Connect TC2030-PKT programming/debugging cable is primarily intended for use in development environments but is also ideal for production programming. The spring-loaded contact pins are held firmly in place by four plastic legs each of which clips securely into its own locating hole.
Tag-Connect TC2030-PKT is ideal where you need to maintain a connection to the PCB for an extended period such as when performing testing or development work.
See also TC2030-PKT-NL for applications where an even smaller footprint is required.
Ideal for both debugging and production programming, the 6 pin plug-of-nails™ cable terminates in a 6 pin 0.1" male SIP strip.
PICkit to 6 Pin Edge-Connect™ (PIC) Debugger mating connector: 6 Pin 0.1" SIP strip Male
Edge-Connect™ - The Leading-Edge Connector!
This special cable has a 6-pin ECV3-06 Edge-Connect™ connector to RJ45 plug.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
Edge-Connect™ is the patent-pending newest member in the family of Programming Connectors and Cables from Tag-Connect. ECV3-06 is the 6-pin connector.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
ECV3-06-PKT has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
New datasheet coming soon. Note that this product terminates in an 6 pin pin-strip connector.
Note: ECV3-06-PKT with ribbon cable and Microchip PICkit 3 connector only supplied, Demo PCB not included.
