View cart “Cortex 10 Pin/SAM LEMTA to 6 Pin Plug-of-Nails™ – No Legs” has been added to your cart.
Tag-Connect™ Solutions for Atmel (Microchip) SAM ARM & ARM Cortex MCUs
Please see below for a list of Tag-Connect™ small footprint debugging/programming cable solutions for Atmel (Microchip) SAM ARM & ARM Cortex MCUs. Solutions may be available for different sized target board connectors, different debugging/programming protocols or different debuggers. Solutions are also available for either “legged” or “no legs” versions of the plug-of-nails™ target board connectors. Use the debugger links to see further information on these options as applicable to particular debuggers.
Cortex 10 Pin/SAM LEMTA solutions with 6 Pin target connector
Cortex 10 Pin/SAM LEMTA to 6 Pin Plug-of-Nails™ - No Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
6-Pin "No Legs" TC2030 Plug-of-Nails™ programming cable for use with ARM Cortex processors.
This special cable has a 6-pin TC2030-NL Tag-Connector and a 10-pin ribbon connector that mates with the FTSH-105 style micro-headers used for Cortex Debug as found in debuggers such as Keil's ULINK-2.
The footprint for the TC2030-CTX-NL Plug-of-Nails™ Connector saves over 66% of the PCB space used by typical FTSH-105 style micro-headers!
Please refer to the TC2030-IDC-NL datasheet below for details of the TC2030-NL footprint.
You may also want to purchase a couple of TC2030-CLIP boards which will hold this cable in place for hands-free programming and debugging.
See also the TC2030-CTX "Legged" version of the cable.
For traditional ARM JTAG solutions using the 20-pin header as found on Segger's J-LINK see our TC2050-ARM2010 adapter used with TC2050-IDC (-NL) cables.
WARNING for ATMEL-ICE users: The Atmel-ICE has it's header pin numbers reversed (standard pin 1 is Atmel-ICE's pin 10). To use our cable with Atmel's reversed pin-number header you'll either need to cut off the ribbon connector locating lug and plug it in backwards, or select the LEMTA option below to order with the 10-pin ribbon connector fitted backwards. If you plug in a standard (correct) Cortex cable you're going to short power and stuff out.Note: Cable only supplied, Keil's ULINK2 debugger and Tag-Connect Demo PCB and additional Legged Cable are shown for illustrative use only - not included with the cable!
Datasheets (TC2030-NL is for footprint information only)
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
Cortex 10 Pin/SAM LEMTA to 6 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
6-Pin Legged TC2030 Plug-of-Nails™ programming cable for use with ARM Cortex processors.
This special cable has a 6-pin TC2030 Tag-Connector and a 10-pin ribbon and ribbon connector that mates with the FTSH-105 style micro-headers used for Cortex Debug Connector as found in debuggers such as Keil's ULINK-2.
See also the TC2030-CTX-NL "No Legs" version of the cable with footprint that saves over 66% of the board space needed by typical FTSH-105 micro headers!
For traditional ARM solutions using the 20-pin header as found on Segger's J-LINK see our TC2050-ARM2010 adapter used with TC2050-IDC (-NL) cables.
WARNING for ATMEL-ICE users: The Atmel-ICE has it's header pin numbers reversed (standard pin 1 is Atmel ICE's pin 10). To use our cable with Atmel's reversed pin-number header you'll either need to cut off the ribbon connector locating lug and plug it in reversed, or select the LEMTA option with the 10-pin connector fitted backwards. If you plug in a standard (correct) Cortex cable you're going to short power and stuff out.Note: Cable only supplied, Keil's ULINK2 debugger and Tag-Connect Demo PCB shown for illustrative use - not included with the cable!
Cortex 10-pin/SAM LEMTA solutions with 10 Pin target connector
Cortex 10-pin/SAM LEMTA to 10 Pin Plug-of-Nails - No Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
The TC2050-IDC-NL-050-ALL programming cable has an 0.050" pitch ribbon connector suitable for programmers and debuggers that use the Samtec FTSH-105-01 style micro-header (10-pins).
The pin connections are 1-1 and all 10 pins are connected. (The standard TC2050-IDC-NL-050 cable does not have pins 5&9 connected to be similar to our TC2050-ARM2010 adapter and may be what you need for ARM applications).
Note: The 10-pin male connectors on the Atmel-ICE have reversed (non-standard) pin numbering. For Atmel-ICE you should purchase the LEMTA version of our cables which have the 10-pin ribbon connector fitted backwards which corrects for the Atmel-ICE pin numbering reversal. (Atmel ICE comes suppplied with a ribbon cable fitted with two 10-pin IDC connectors and a 6-pin single-in-line SIP connector - The 10-pin connector at the Atmel ICE end is reversed but the other is not, correcting the pin-numbering at the target PCB. Our LEMTA cables similarly have a reversed connector).
Orientation: LEMTA - Ribbon Connector reversed for Atmel-ICE
TC2050 10 Pin “No legs” Plug-of-Nails™ to 0.050″ pitch 10 pin ribbon connector suitable for ULINK2 and similar debuggers that use the Samtec FTSH-105-01 style micro-header. As TC2050-IDC-NL-050 but with all pins connected.
This product is intended to temporarily hold a TC2050-NL cable in place on a PCB. The solution will help when board space is premium and you need to perform a hands-free programming or debugging operation. For a more robust and convenient debugging connection consider using the TC2050 legged cable and footprint. Supplied as pack of 3.
We recommend keeping a few spare of these since they are easily misplaced when working on the desktop. Over time they may lose some grip.
Cortex 10-pin/SAM LEMTA to 10 Pin Plug-of-Nails - With Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
The TC2050-IDC-050-ALL programming cable has an 0.050" pitch ribbon connector suitable for ULINK2 and similar debuggers that use the Samtec FTSH-105-01 style micro-header.
The pin connections are 1-1 and all 10 pins are connected. (The standard TC2050-IDC-050 cable does not have pins 5&9 connected to be similar to our TC2050-ARM2010 adapter).
Note: The 10-pin male connectors on the Atmel-ICE have reversed (non-standard) pin numbering. For Atmel-ICE you should purchase the LEMTA version of our cables which have the 10-pin ribbon connector fitted backwards which corrects for the Atmel-ICE pin numbering reversal. (Atmel ICE comes suppplied with a ribbon cable fitted with two 10-pin IDC connectors and a 6-pin single-in-line SIP connector - The 10-pin connector at the Atmel ICE end is reversed but the other is not, correcting the pin-numbering at the target PCB. Our LEMTA cables similarly have a reversed connector).
Orientation: LEMTA - Ribbon Connector reversed for Atmel-ICE
TC2050 10 Pin “Legged ” Plug-of-Nails™ to 0.050″ pitch 10 pin ribbon connector suitable for ULINK2 and similar debuggers that use the Samtec FTSH-105-01 style micro-header. As TC2050-IDC-050 but all pins connected.
We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.OkPrivacy policy