Both solutions are similar in that they use a 20-pin to Tag-Connect adapter. However, the Full Traditional JTAG also allows you to optionally power the target from the debugger and provides access to all of the signals provided by the traditional 20-pin ARM 0.1″ connection whereas the SWD (Serial Wire Debug)solution only supplies access to the signals used by the SWD protocol.
Full Traditional JTAG using TC2050 and TC2050-ARM2010 adapter
Both solutions for the ST-LINK/V2 are similar in that it requires an adapter and a cable, so it is up to you which one you will go for depending on your PCB needs. Here is the first solution:
Both “legged” and “no-leg” cables come in the standard 6″ length.
The TC2050-IDC-NL will require the TC2050-CLIP if you want a hands-free solution while debugging.
The TC2050-ARM2010 is a Tag-Connect adapter board allowing our TC2050-IDC cables to be used for ARM JTAG and ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2050-IDC Plug-of-Nails™ Cables, the adapter may be useful to people wishing to use 10-pin 0.1" ribbon headers on their PCB.
Picture shows Segger JLINK, an TC2050-ARM2010 adapter pcb and a TC2050-IDC cable.
For Lauterbach programmers/debuggers with 20-pin 0.1″ female IDC connector, please see the alternative TC2050-ARM2010-M adapter instead.
Note: Adapter only supplied, debugger and cable not included!
The ECV3-10-IDC is a 10-pin Edge-Connect™ connector terminated in a 10-pin 0.1″ pitch female IDC. This uses version 3 of our patented literal edge of the board connector which more robust and more convenient than previous versions.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future. ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
Edge-Connect™ is the patent-pending newest member in the family of Programming Connectors and Cables from Tag-Connect. EC10-IDC is the 10-pin version.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™ so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
EC10-IDC has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
See below for the latest datasheets. We will be publishing revisions to the datasheets.
Note: ECV3-10-IDC with ribbon cable and IDC connector only supplied, Demo PCB not included.
The TC2050-ARM2010 is a Tag-Connect adapter board allowing our TC2050-IDC cables to be used for ARM JTAG and ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2050-IDC Plug-of-Nails™ Cables, the adapter may be useful to people wishing to use 10-pin 0.1" ribbon headers on their PCB.
Picture shows Segger JLINK, an TC2050-ARM2010 adapter pcb and a TC2050-IDC cable.
For Lauterbach programmers/debuggers with 20-pin 0.1″ female IDC connector, please see the alternative TC2050-ARM2010-M adapter instead.
Note: Adapter only supplied, debugger and cable not included!
Tag-Connect's TC2050-IDC-NL "No Legs" Plug-of-Nails™ programming cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1" ribbon connector.
Plugs straight to your PCB - No mating connector or header required!
Requires only a tiny 0.03" footprint of pads and locating holes in your PCB.
Zero Cost Per Board!
Tiny Footprint!
High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.
Footprint has no height and can reduce the size and space requirements of your PCB.
A great way to make test and debug signals available at no cost and with minimal board space.
Can be retained in place using a TC2050-CLIP board.
Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB's while lowering board costs and facilitating efficient production programming. Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.
The tiny "No Legs" footprint takes only 0.03 square inches (about the same board space as a couple of SMT resistors) which means you can locate the footprint right next to the MCU if desired.
This 10-conductor cable has a TC2050-NL Tag-Connector on one end and a standard 0.1" ribbon connector on the other and is suitable for use with most many MCUs / FPGAs and JTAG programming and debug operations.
A growing range of adaptors are available for specific and generic applications such as Xilinx SPARTAN and VERTEX FPGAs, TI MSP430 (TC2050-IDC-430), etc
Also available in self-retaining "legged" version TC2050-IDC.
This product is intended to temporarily hold a TC2050-NL cable in place on a PCB. The solution will help when board space is premium and you need to perform a hands-free programming or debugging operation. For a more robust and convenient debugging connection consider using the TC2050 legged cable and footprint. Supplied as pack of 3.
We recommend keeping a few spare of these since they are easily misplaced when working on the desktop. Over time they may lose some grip.
The TC2050-ARM2010 is a Tag-Connect adapter board allowing our TC2050-IDC cables to be used for ARM JTAG and ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2050-IDC Plug-of-Nails™ Cables, the adapter may be useful to people wishing to use 10-pin 0.1" ribbon headers on their PCB.
Picture shows Segger JLINK, an TC2050-ARM2010 adapter pcb and a TC2050-IDC cable.
For Lauterbach programmers/debuggers with 20-pin 0.1″ female IDC connector, please see the alternative TC2050-ARM2010-M adapter instead.
Note: Adapter only supplied, debugger and cable not included!
Tag-Connect's TC2050-IDC "Legged" Plug-of-Nails™ programming cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1" ribbon connector.
Plugs straight to your PCB - No mating connector or header required!
Requires only a tiny footprint of pads and locating holes in your PCB.
Zero Cost Per Board!
Tiny Footprint!
High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.
Footprint has no height and can reduce the size and space requirements of your PCB.
A great way to make test and debug signals available at no cost and with minimal board space.
Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB's while lowering board costs and facilitating efficient production programming. Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.
The legged version footprint takes about the same board space as two or three SMT resistors which means you can locate the footprint right next to the MCU if desired.
This 10-conductor cable has a TC2050 Tag-Connector on one end and a standard 0.1" ribbon connector on the other and is suitable for use with most many MCUs / FPGAs and JTAG programming and debug operations.
A growing range of adaptors are available for specific and generic applications such as Xilinx SPARTAN and VERTEX FPGAs, TI MSP430 (TC2050-IDC-430), etc
See also TC2050-IDC-NL (no-legs) version with a tiny 0.03” footprint.
*Debugger not included. Some easy assembly required.
Attach the ARM20-CTX to the ST-LINK/V2 debugger, then the TC2030-IDC cable to the ARM20-CTX adapter and you’re all set to go!
Both “legged” and “no-leg” cables come in the standard 6″ length.
The TC2030-IDC-NL will require the TC2030-CLIP if you want a hands-free solution while debugging.
The Tag-Connect ARM20-CTX adapter board allows our TC2030-IDC cables to be used for ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2030-IDC (and TC2030-IDC-NL) Plug-of-Nails™ Cables, the adapter may also be useful to people wishing to use 6-pin 0.1" ribbon headers on their PCB instead of the traditional 20-Pin header.
For Lauterbach programmers/debuggers with 20-pin 0.1" female IDC connector, please see the alternative ARM20-CTX-M adapter.
Note: Adapter only supplied. The TC2030-IDC or TC2030-IDC-NL cable is purchased separately, the cables and Segger JLINK seen in the pictures are not included!
The ECV3-06-IDC is a 6-pin Edge-Connect™ connector terminated in a 6-pin 0.1" pitch female IDC. This uses version 3 of our patented literal edge of the board connector which more robust and more convenient than previous versions.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
Edge-Connect™ is the patented newest member in the family of Programming Connectors and Cables from Tag-Connect. ECV3-06 is the 6-pin version.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCBs and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
EC-06 has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
See below for the latest datasheets. We will be publishing revisions to the datasheet.
Note: ECV3-06 with ribbon cable and IDC connector only supplied, Demo PCB not included.
The Tag-Connect ARM20-CTX adapter board allows our TC2030-IDC cables to be used for ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2030-IDC (and TC2030-IDC-NL) Plug-of-Nails™ Cables, the adapter may also be useful to people wishing to use 6-pin 0.1" ribbon headers on their PCB instead of the traditional 20-Pin header.
For Lauterbach programmers/debuggers with 20-pin 0.1" female IDC connector, please see the alternative ARM20-CTX-M adapter.
Note: Adapter only supplied. The TC2030-IDC or TC2030-IDC-NL cable is purchased separately, the cables and Segger JLINK seen in the pictures are not included!
The TC2030-IDC is our "Legged" 6-pin Plug-of-Nails™ programming cable fitted with a 6-pin 0.1" pitch ribbon connector.
The "Legged" or "With Legs" versions of our cables snap directly into a tiny footprint of holes and pads in your PCB. By eliminating the need for a mating header component, you not only save PCB space but also cost on every board!
See TC2030-IDC-NL for the "No Legs" version which has an even smaller footprint of about the size of an 0805 SMT resistor.
Popular applications include programming Atmel AVR, many Renesas MCU's (when used with our TC-Renesas E1 / E8a adapter) and Zilog. Also great for bringing our SPI / IIC / RS232 and test signal access.
Also available in 10" lengths (TC2030-IDC-10). Contact us for 36" length versions of these cables.
The Tag-Connect ARM20-CTX adapter board allows our TC2030-IDC cables to be used for ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2030-IDC (and TC2030-IDC-NL) Plug-of-Nails™ Cables, the adapter may also be useful to people wishing to use 6-pin 0.1" ribbon headers on their PCB instead of the traditional 20-Pin header.
For Lauterbach programmers/debuggers with 20-pin 0.1" female IDC connector, please see the alternative ARM20-CTX-M adapter.
Note: Adapter only supplied. The TC2030-IDC or TC2030-IDC-NL cable is purchased separately, the cables and Segger JLINK seen in the pictures are not included!
The TC2030-IDC-NL is our "No Legs" 6-pin Plug-of-Nails™ programming cable fitted with a 6-pin 0.1" pitch ribbon connector.
With its tiny 0.02 sq inch footprint the TC2030 Tag-Connector has a footprint using about the same PCB space as an 0805 resistor.
The "No Legs" versions of our cables are designed to be held in place by hand for a fast programming operation or can be temporarily retained in place for debugging when used with our TC2030-CLIP boards.
See TC2030-IDC for the "Legged" version which has four additional feet which hold it securely in place on the PCB for debugging or programming use.
Popular applications include programming Atmel AVR, many Renesas MCU's (when used with our TC-Renesas E1 / E8a adapter) and Zilog. Also great for bringing our SPI / IIC / RS232 and test signal access.
Also available in 10"/254mm lengths (TC2030-IDC-NL-10). Contact us for 36" length versions of these cables.
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
This debug cable is a TC2030-MCP-NL modified to have a 4-pin connector that plugs to the SWIM connector on ST-LINK/V2 for STM8 MCUs. This is the no-legs version of the TC2030 Plug-of-Nails™ connector.
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
This debug cable is a TC2030-MCP modified to have a 4-pin connector that plugs to the SWIM connector on ST-LINK/V2 for STM8 MCUs. This is the legged version of the TC2030 Plug-of-Nails™ connector.
1 x TC2030-IDC-NL
1 x TC2030-SWIM-NL
1 x TC2030-SWIM