Please see below for a list of Tag-Connect™ small footprint debugging/programming cable solutions for ARM & ARM Cortex devices. Solutions may be available for different sized target board connectors, different debugging/programming protocols or different debuggers. Solutions are also available for either “legged” or “no legs” versions of the plug-of-nails™ target board connectors. Use the debugger links to see further information on these options as applicable to particular debuggers.
ARM20 to 6 Pin Plug-of-Nails™ - No Legs Debugger mating connector: 20 Pin IDC 0.1" Female
The Tag-Connect ARM20-CTX adapter board allows our TC2030-IDC cables to be used for ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2030-IDC (and TC2030-IDC-NL) Plug-of-Nails™ Cables, the adapter may also be useful to people wishing to use 6-pin 0.1" ribbon headers on their PCB instead of the traditional 20-Pin header.
For Lauterbach programmers/debuggers with 20-pin 0.1" female IDC connector, please see the alternative ARM20-CTX-M adapter.
Note: Adapter only supplied. The TC2030-IDC or TC2030-IDC-NL cable is purchased separately, the cables and Segger JLINK seen in the pictures are not included!
The TC2030-IDC-NL is our "No Legs" 6-pin Plug-of-Nails™ programming cable fitted with a 6-pin 0.1" pitch ribbon connector.
With its tiny 0.02 sq inch footprint the TC2030 Tag-Connector has a footprint using about the same PCB space as an 0805 resistor.
The "No Legs" versions of our cables are designed to be held in place by hand for a fast programming operation or can be temporarily retained in place for debugging when used with our TC2030-CLIP boards.
See TC2030-IDC for the "Legged" version which has four additional feet which hold it securely in place on the PCB for debugging or programming use.
Popular applications include programming Atmel AVR, many Renesas MCU's (when used with our TC-Renesas E1 / E8a adapter) and Zilog. Also great for bringing our SPI / IIC / RS232 and test signal access.
Also available in 10"/254mm lengths (TC2030-IDC-NL-10). Contact us for 36" length versions of these cables.
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
ARM20 to 6 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 20 Pin IDC 0.1" Female
The Tag-Connect ARM20-CTX adapter board allows our TC2030-IDC cables to be used for ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2030-IDC (and TC2030-IDC-NL) Plug-of-Nails™ Cables, the adapter may also be useful to people wishing to use 6-pin 0.1" ribbon headers on their PCB instead of the traditional 20-Pin header.
For Lauterbach programmers/debuggers with 20-pin 0.1" female IDC connector, please see the alternative ARM20-CTX-M adapter.
Note: Adapter only supplied. The TC2030-IDC or TC2030-IDC-NL cable is purchased separately, the cables and Segger JLINK seen in the pictures are not included!
The TC2030-IDC is our "Legged" 6-pin Plug-of-Nails™ programming cable fitted with a 6-pin 0.1" pitch ribbon connector.
The "Legged" or "With Legs" versions of our cables snap directly into a tiny footprint of holes and pads in your PCB. By eliminating the need for a mating header component, you not only save PCB space but also cost on every board!
See TC2030-IDC-NL for the "No Legs" version which has an even smaller footprint of about the size of an 0805 SMT resistor.
Popular applications include programming Atmel AVR, many Renesas MCU's (when used with our TC-Renesas E1 / E8a adapter) and Zilog. Also great for bringing our SPI / IIC / RS232 and test signal access.
Also available in 10" lengths (TC2030-IDC-10). Contact us for 36" length versions of these cables.
The Tag-Connect ARM20-CTX adapter board allows our TC2030-IDC cables to be used for ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2030-IDC (and TC2030-IDC-NL) Plug-of-Nails™ Cables, the adapter may also be useful to people wishing to use 6-pin 0.1" ribbon headers on their PCB instead of the traditional 20-Pin header.
For Lauterbach programmers/debuggers with 20-pin 0.1" female IDC connector, please see the alternative ARM20-CTX-M adapter.
Note: Adapter only supplied. The TC2030-IDC or TC2030-IDC-NL cable is purchased separately, the cables and Segger JLINK seen in the pictures are not included!
The ECV3-06-IDC is a 6-pin Edge-Connect™ connector terminated in a 6-pin 0.1" pitch female IDC. This uses version 3 of our patented literal edge of the board connector which more robust and more convenient than previous versions.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
Edge-Connect™ is the patented newest member in the family of Programming Connectors and Cables from Tag-Connect. ECV3-06 is the 6-pin version.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCBs and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
EC-06 has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
See below for the latest datasheets. We will be publishing revisions to the datasheet.
Note: ECV3-06 with ribbon cable and IDC connector only supplied, Demo PCB not included.
ARM20 to 10 Pin Plug-of-Nails™ - No Legs Debugger mating connector: 20 Pin IDC 0.1" Female
The TC2050-ARM2010 is a Tag-Connect adapter board allowing our TC2050-IDC cables to be used for ARM JTAG and ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2050-IDC Plug-of-Nails™ Cables, the adapter may be useful to people wishing to use 10-pin 0.1" ribbon headers on their PCB.
Picture shows Segger JLINK, an TC2050-ARM2010 adapter pcb and a TC2050-IDC cable.
For Lauterbach programmers/debuggers with 20-pin 0.1″ female IDC connector, please see the alternative TC2050-ARM2010-M adapter instead.
Note: Adapter only supplied, debugger and cable not included!
Tag-Connect's TC2050-IDC-NL "No Legs" Plug-of-Nails™ programming cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1" ribbon connector.
Plugs straight to your PCB - No mating connector or header required!
Requires only a tiny 0.03" footprint of pads and locating holes in your PCB.
Zero Cost Per Board!
Tiny Footprint!
High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.
Footprint has no height and can reduce the size and space requirements of your PCB.
A great way to make test and debug signals available at no cost and with minimal board space.
Can be retained in place using a TC2050-CLIP board.
Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB's while lowering board costs and facilitating efficient production programming. Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.
The tiny "No Legs" footprint takes only 0.03 square inches (about the same board space as a couple of SMT resistors) which means you can locate the footprint right next to the MCU if desired.
This 10-conductor cable has a TC2050-NL Tag-Connector on one end and a standard 0.1" ribbon connector on the other and is suitable for use with most many MCUs / FPGAs and JTAG programming and debug operations.
A growing range of adaptors are available for specific and generic applications such as Xilinx SPARTAN and VERTEX FPGAs, TI MSP430 (TC2050-IDC-430), etc
Also available in self-retaining "legged" version TC2050-IDC.
This product is intended to temporarily hold a TC2050-NL cable in place on a PCB. The solution will help when board space is premium and you need to perform a hands-free programming or debugging operation. For a more robust and convenient debugging connection consider using the TC2050 legged cable and footprint. Supplied as pack of 3.
We recommend keeping a few spare of these since they are easily misplaced when working on the desktop. Over time they may lose some grip.
ARM20 to 10 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 20 Pin IDC 0.1" Female
The TC2050-ARM2010 is a Tag-Connect adapter board allowing our TC2050-IDC cables to be used for ARM JTAG and ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2050-IDC Plug-of-Nails™ Cables, the adapter may be useful to people wishing to use 10-pin 0.1" ribbon headers on their PCB.
Picture shows Segger JLINK, an TC2050-ARM2010 adapter pcb and a TC2050-IDC cable.
For Lauterbach programmers/debuggers with 20-pin 0.1″ female IDC connector, please see the alternative TC2050-ARM2010-M adapter instead.
Note: Adapter only supplied, debugger and cable not included!
Tag-Connect's TC2050-IDC "Legged" Plug-of-Nails™ programming cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1" ribbon connector.
Plugs straight to your PCB - No mating connector or header required!
Requires only a tiny footprint of pads and locating holes in your PCB.
Zero Cost Per Board!
Tiny Footprint!
High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.
Footprint has no height and can reduce the size and space requirements of your PCB.
A great way to make test and debug signals available at no cost and with minimal board space.
Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB's while lowering board costs and facilitating efficient production programming. Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.
The legged version footprint takes about the same board space as two or three SMT resistors which means you can locate the footprint right next to the MCU if desired.
This 10-conductor cable has a TC2050 Tag-Connector on one end and a standard 0.1" ribbon connector on the other and is suitable for use with most many MCUs / FPGAs and JTAG programming and debug operations.
A growing range of adaptors are available for specific and generic applications such as Xilinx SPARTAN and VERTEX FPGAs, TI MSP430 (TC2050-IDC-430), etc
See also TC2050-IDC-NL (no-legs) version with a tiny 0.03” footprint.
The TC2050-ARM2010 is a Tag-Connect adapter board allowing our TC2050-IDC cables to be used for ARM JTAG and ARM SWD (Serial Wire Debug) applications. Although intended for use with our patented TC2050-IDC Plug-of-Nails™ Cables, the adapter may be useful to people wishing to use 10-pin 0.1" ribbon headers on their PCB.
Picture shows Segger JLINK, an TC2050-ARM2010 adapter pcb and a TC2050-IDC cable.
For Lauterbach programmers/debuggers with 20-pin 0.1″ female IDC connector, please see the alternative TC2050-ARM2010-M adapter instead.
Note: Adapter only supplied, debugger and cable not included!
The ECV3-10-IDC is a 10-pin Edge-Connect™ connector terminated in a 10-pin 0.1″ pitch female IDC. This uses version 3 of our patented literal edge of the board connector which more robust and more convenient than previous versions.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future. ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
Edge-Connect™ is the patent-pending newest member in the family of Programming Connectors and Cables from Tag-Connect. EC10-IDC is the 10-pin version.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™ so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
EC10-IDC has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
See below for the latest datasheets. We will be publishing revisions to the datasheets.
Note: ECV3-10-IDC with ribbon cable and IDC connector only supplied, Demo PCB not included.
Cortex 10 Pin solutions with 6 Pin target connector
Cortex 10 Pin to 6 Pin Plug-of-Nails™ - No Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
6-Pin "No Legs" TC2030 Plug-of-Nails™ programming cable for use with ARM Cortex processors.
This special cable has a 6-pin TC2030-NL Tag-Connector and a 10-pin ribbon connector that mates with the FTSH-105 style micro-headers used for Cortex Debug as found in debuggers such as Keil's ULINK-2.
The footprint for the TC2030-CTX-NL Plug-of-Nails™ Connector saves over 66% of the PCB space used by typical FTSH-105 style micro-headers!
Please refer to the TC2030-IDC-NL datasheet below for details of the TC2030-NL footprint.
You may also want to purchase a couple of TC2030-CLIP boards which will hold this cable in place for hands-free programming and debugging.
See also the TC2030-CTX "Legged" version of the cable.
For traditional ARM JTAG solutions using the 20-pin header as found on Segger's J-LINK see our TC2050-ARM2010 adapter used with TC2050-IDC (-NL) cables.
WARNING for ATMEL-ICE users: The Atmel-ICE has it's header pin numbers reversed (standard pin 1 is Atmel-ICE's pin 10). To use our cable with Atmel's reversed pin-number header you'll either need to cut off the ribbon connector locating lug and plug it in backwards, or select the LEMTA option below to order with the 10-pin ribbon connector fitted backwards. If you plug in a standard (correct) Cortex cable you're going to short power and stuff out.Note: Cable only supplied, Keil's ULINK2 debugger and Tag-Connect Demo PCB and additional Legged Cable are shown for illustrative use only - not included with the cable!
Datasheets (TC2030-NL is for footprint information only)
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
Cortex 10 Pin to 6 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
6-Pin Legged TC2030 Plug-of-Nails™ programming cable for use with ARM Cortex processors.
This special cable has a 6-pin TC2030 Tag-Connector and a 10-pin ribbon and ribbon connector that mates with the FTSH-105 style micro-headers used for Cortex Debug Connector as found in debuggers such as Keil's ULINK-2.
See also the TC2030-CTX-NL "No Legs" version of the cable with footprint that saves over 66% of the board space needed by typical FTSH-105 micro headers!
For traditional ARM solutions using the 20-pin header as found on Segger's J-LINK see our TC2050-ARM2010 adapter used with TC2050-IDC (-NL) cables.
WARNING for ATMEL-ICE users: The Atmel-ICE has it's header pin numbers reversed (standard pin 1 is Atmel ICE's pin 10). To use our cable with Atmel's reversed pin-number header you'll either need to cut off the ribbon connector locating lug and plug it in reversed, or select the LEMTA option with the 10-pin connector fitted backwards. If you plug in a standard (correct) Cortex cable you're going to short power and stuff out.Note: Cable only supplied, Keil's ULINK2 debugger and Tag-Connect Demo PCB shown for illustrative use - not included with the cable!
Cortex 10 Pin to 6 Pin Edge-Connect™ Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
Edge-Connect™ - The Leading-Edge Connector!
This special cable has a 6-pin ECV3-06 Edge-Connect™ connector and a 10-pin 0.05" pitch female IDC that mates with the FTSH-105 style micro-headers used for the Cortex Debug Connector as found in debuggers such as Keil’s ULINK-2. This uses version 3 of our patented literal edge of the board connector which is more robust and more convenient than previous versions.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
WARNING for ATMEL-ICE users: The Atmel-ICE has it’s header pin numbers reversed (standard pin 1 is Atmel ICE’s pin 10). To use our cable with Atmel’s reversed pin-number header you’ll either need to cut off the ribbon connector locating lug and plug it in reversed, or select the LEMTA option with the 10-pin connector fitted backwards. If you plug in a standard (correct) Cortex cable you’re going to short power and stuff out.Edge-Connect™ is the patent-pending newest member in the family of Programming Connectors and Cables from Tag-Connect. ECV3-06 is the 6-pin connector.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
ECV3-06-CTX has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
New datasheet coming soon. Note that this product terminates in a 10-pin 0.05" IDC.
Note: ECV3-06-CTX with ribbon cable and IDC connector only supplied, Demo PCB not included.
Cortex 10 Pin/SAM LEMTA solutions with 6 Pin target connector
Cortex 10 Pin/SAM LEMTA to 6 Pin Plug-of-Nails™ - No Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
6-Pin "No Legs" TC2030 Plug-of-Nails™ programming cable for use with ARM Cortex processors.
This special cable has a 6-pin TC2030-NL Tag-Connector and a 10-pin ribbon connector that mates with the FTSH-105 style micro-headers used for Cortex Debug as found in debuggers such as Keil's ULINK-2.
The footprint for the TC2030-CTX-NL Plug-of-Nails™ Connector saves over 66% of the PCB space used by typical FTSH-105 style micro-headers!
Please refer to the TC2030-IDC-NL datasheet below for details of the TC2030-NL footprint.
You may also want to purchase a couple of TC2030-CLIP boards which will hold this cable in place for hands-free programming and debugging.
See also the TC2030-CTX "Legged" version of the cable.
For traditional ARM JTAG solutions using the 20-pin header as found on Segger's J-LINK see our TC2050-ARM2010 adapter used with TC2050-IDC (-NL) cables.
WARNING for ATMEL-ICE users: The Atmel-ICE has it's header pin numbers reversed (standard pin 1 is Atmel-ICE's pin 10). To use our cable with Atmel's reversed pin-number header you'll either need to cut off the ribbon connector locating lug and plug it in backwards, or select the LEMTA option below to order with the 10-pin ribbon connector fitted backwards. If you plug in a standard (correct) Cortex cable you're going to short power and stuff out.Note: Cable only supplied, Keil's ULINK2 debugger and Tag-Connect Demo PCB and additional Legged Cable are shown for illustrative use only - not included with the cable!
Datasheets (TC2030-NL is for footprint information only)
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
Cortex 10 Pin/SAM LEMTA to 6 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
6-Pin Legged TC2030 Plug-of-Nails™ programming cable for use with ARM Cortex processors.
This special cable has a 6-pin TC2030 Tag-Connector and a 10-pin ribbon and ribbon connector that mates with the FTSH-105 style micro-headers used for Cortex Debug Connector as found in debuggers such as Keil's ULINK-2.
See also the TC2030-CTX-NL "No Legs" version of the cable with footprint that saves over 66% of the board space needed by typical FTSH-105 micro headers!
For traditional ARM solutions using the 20-pin header as found on Segger's J-LINK see our TC2050-ARM2010 adapter used with TC2050-IDC (-NL) cables.
WARNING for ATMEL-ICE users: The Atmel-ICE has it's header pin numbers reversed (standard pin 1 is Atmel ICE's pin 10). To use our cable with Atmel's reversed pin-number header you'll either need to cut off the ribbon connector locating lug and plug it in reversed, or select the LEMTA option with the 10-pin connector fitted backwards. If you plug in a standard (correct) Cortex cable you're going to short power and stuff out.Note: Cable only supplied, Keil's ULINK2 debugger and Tag-Connect Demo PCB shown for illustrative use - not included with the cable!
Cortex 10 Pin/SAM LEMTA to 6 Pin Edge-Connect™ Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
Edge-Connect™ - The Leading-Edge Connector!
This special cable has a 6-pin ECV3-06 Edge-Connect™ connector and a 10-pin 0.05" pitch female IDC that mates with the FTSH-105 style micro-headers used for the Cortex Debug Connector as found in debuggers such as Keil’s ULINK-2. This uses version 3 of our patented literal edge of the board connector which is more robust and more convenient than previous versions.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
WARNING for ATMEL-ICE users: The Atmel-ICE has it’s header pin numbers reversed (standard pin 1 is Atmel ICE’s pin 10). To use our cable with Atmel’s reversed pin-number header you’ll either need to cut off the ribbon connector locating lug and plug it in reversed, or select the LEMTA option with the 10-pin connector fitted backwards. If you plug in a standard (correct) Cortex cable you’re going to short power and stuff out.Edge-Connect™ is the patent-pending newest member in the family of Programming Connectors and Cables from Tag-Connect. ECV3-06 is the 6-pin connector.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
ECV3-06-CTX has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
New datasheet coming soon. Note that this product terminates in a 10-pin 0.05" IDC.
Note: ECV3-06-CTX with ribbon cable and IDC connector only supplied, Demo PCB not included.
Cortex 20 Pin solutions with 6 Pin target connector
Cortex 20 Pin to 6 Pin Plug-of-Nails™ - No Legs Debugger mating connector: 20 Pin IDC 0.05" Female (Mates with FTSH)
This Cortex programming cable is the same as the TC2030-CTX-NL cable except it has a 0.05" (1.27mm) pitch 20-pin connector compatible with i-Jet and ULINK pro. This won't fit the traditional 20-pin 0.1" connector such as found on the standard J-Link debuggers).
The cable itself has a ten pin ribbon cable and 6-pin TC2030-NL "No legs" Tag-Connect small footprint supporting ARM Cortex MCU's.
Note: Cable only supplied, IAR's I-JET and demo board not included!
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
Cortex 20 Pin to 6 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 20 Pin IDC 0.05" Female (Mates with FTSH)
This Cortex programming cable is the same as the TC2030-CTX cable except it has a 0.05" (1.27mm) pitch 20-pin connector compatible with i-Jet and ULINK pro. This won't fit the traditional 20-pin 0.1" connector such as found on the standard J-Link debuggers).
The cable itself has a ten pin ribbon cable and 6-pin TC2030 Tag-Connect footprint supporting ARM Cortex MCU's.
Note: Cable only supplied, IAR's I-JET and demo board not included!
Cortex 20 Pin to 6 Pin Edge-Connect™ Debugger mating connector: 20 Pin IDC 0.05" Female (Mates with FTSH)
Edge-Connect™ - The Leading-Edge Connector!
This special cable has a 6-pin ECV3-06 Edge-Connect™ connector and a 20-pin 0.05″ pitch female IDC that mates with the 20-pin Cortex debug connector as found in debuggers such as IAR’s I-Jet or Keil’s ULINKpro. This uses version 3 of our patented literal edge of the board connector which is more robust and more convenient than previous versions.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
Edge-Connect™ is the patent-pending newest member in the family of Programming Connectors and Cables from Tag-Connect. ECV3-06 is the 6-pin connector.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
ECV3-06-CTX-20 has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
New datasheet coming soon. Note that this product terminates in a 20-pin 0.05" IDC.
Note: ECV3-06-CTX-20 with ribbon cable and 20-pin Cortex connector only supplied, Demo PCB not included.
Cortex 20 Pin solutions with 6+10 Pin target connector
Cortex 20 Pin to 6 Pin + 10 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 20 Pin IDC 0.05" Female (Mates with FTSH)
TC2030-CTX-ETM is a TC2030-CTX-20 programming cable with 6-pin Tag-Connector for SWD and an additional 10-pin TC2050 connector connected to pins 11-20 providing the extended trace signals.
The pin numbering for pins 11-20 of the 0.05" pitch 20-pin Cortex maps to the TC2050 pin numbering as follows (TC2050 pins are numbered like a DIP IC).
TC2050 pin no.
Cortex 20-pin
1
11 GND/TgtPwr+cap
2
13 GND/TgtPwr+cap
3
15 GND
4
17 GND
5
19 GND
6
20 TRACEDATA[3]
7
18 TRACEDATA[2]
8
16 TRACEDATA[1]
9
14 TRACEDATA[0]
10
12 TRACECLK
TC2030 pin no.
SWD signal
1
1 VCC
2
2 SWDIO
3
10 nRESET
4
4 SWCLK
5
3,5,9 GND
6
6 SWO
Please Note: Be sure to follow manufacturer's advice on signal integrity and termination during design and layout.
Cortex 10 Pin solutions with 10 Pin target connector
Cortex 10 Pin to 10 Pin Plug-of-Nails™ - No Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
The TC2050-IDC-NL-050-ALL programming cable has an 0.050" pitch ribbon connector suitable for programmers and debuggers that use the Samtec FTSH-105-01 style micro-header (10-pins).
The pin connections are 1-1 and all 10 pins are connected. (The standard TC2050-IDC-NL-050 cable does not have pins 5&9 connected to be similar to our TC2050-ARM2010 adapter and may be what you need for ARM applications).
Note: The 10-pin male connectors on the Atmel-ICE have reversed (non-standard) pin numbering. For Atmel-ICE you should purchase the LEMTA version of our cables which have the 10-pin ribbon connector fitted backwards which corrects for the Atmel-ICE pin numbering reversal. (Atmel ICE comes suppplied with a ribbon cable fitted with two 10-pin IDC connectors and a 6-pin single-in-line SIP connector - The 10-pin connector at the Atmel ICE end is reversed but the other is not, correcting the pin-numbering at the target PCB. Our LEMTA cables similarly have a reversed connector).
TC2050 10 Pin “No legs” Plug-of-Nails™ to 0.050″ pitch 10 pin ribbon connector suitable for ULINK2 and similar debuggers that use the Samtec FTSH-105-01 style micro-header. As TC2050-IDC-NL-050 but with all pins connected.
This product is intended to temporarily hold a TC2050-NL cable in place on a PCB. The solution will help when board space is premium and you need to perform a hands-free programming or debugging operation. For a more robust and convenient debugging connection consider using the TC2050 legged cable and footprint. Supplied as pack of 3.
We recommend keeping a few spare of these since they are easily misplaced when working on the desktop. Over time they may lose some grip.
Cortex 10 Pin to 10 Pin Plug-of-Nails™ - With Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
The TC2050-IDC-050-ALL programming cable has an 0.050" pitch ribbon connector suitable for ULINK2 and similar debuggers that use the Samtec FTSH-105-01 style micro-header.
The pin connections are 1-1 and all 10 pins are connected. (The standard TC2050-IDC-050 cable does not have pins 5&9 connected to be similar to our TC2050-ARM2010 adapter).
Note: The 10-pin male connectors on the Atmel-ICE have reversed (non-standard) pin numbering. For Atmel-ICE you should purchase the LEMTA version of our cables which have the 10-pin ribbon connector fitted backwards which corrects for the Atmel-ICE pin numbering reversal. (Atmel ICE comes suppplied with a ribbon cable fitted with two 10-pin IDC connectors and a 6-pin single-in-line SIP connector - The 10-pin connector at the Atmel ICE end is reversed but the other is not, correcting the pin-numbering at the target PCB. Our LEMTA cables similarly have a reversed connector).
TC2050 10 Pin “Legged ” Plug-of-Nails™ to 0.050″ pitch 10 pin ribbon connector suitable for ULINK2 and similar debuggers that use the Samtec FTSH-105-01 style micro-header. As TC2050-IDC-050 but all pins connected.
Cortex 10 Pin to 10 Pin Edge-Connect™ Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
Edge-Connect™ - The Leading-Edge Connector!
The ECV3-10-IDC-050 is a 10-pin Edge-Connect™ connector terminated in a 10-pin 0.05" pitch female IDC. This uses version 3 of our patented literal edge of the board connector which is more robust and more convenient than previous versions. The ECV3-10-IDC-050 is suitable for ULINK2 and similar debuggers that use the Samtec FTSH-105-01 style micro-header. This cable is the equivalent to using our TC2050-ARM2010 adapter with a ECV3-10-IDC cable connected to the ULINK2’s 20-pin 0.1″ pitch traditional ARM JTAG header. The pin connections are 1-1. All 10 pins are connected.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
We generally recommend choosing the ECV3-10-IDC or EC06-IDC cables over this ECV3-10-IDC-050 because cables mating to the Cortex 10-pin 0.050″ header use very fine 0.025″ pitch ribbon cable with very few strands of tinned copper wire in each wire of the ribbon. These fine strands can break over time through flexing and stressing. The thicker ribbon cables used with our ECV3-10-IDC or ECV3-06-IDC cables have many times the cross-sectional area of copper and make for a far more robust solution.
Note: The 10-pin male connectors on the Atmel-ICE have reversed (non-standard) pin numbering. For Atmel-ICE you should purchase the LEMTA version of our cables which have the 10-pin ribbon connector fitted backwards which corrects for the Atmel-ICE pin numbering reversal. (Atmel ICE comes supplied with a ribbon cable fitted with two 10-pin IDC connectors and a 6-pin single-in-line SIP connector - The 10-pin connector at the Atmel ICE end is reversed but the other is not, correcting the pin-numbering at the target PCB. Our LEMTA cables similarly have a reversed connector).
Edge-Connect™ is the patent-pending newest member in the family of Programming Connectors and Cables from Tag-Connect.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
ECV3-10-IDC-050 has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
See below for the EC10-IDC version 1 datasheet for PCB dimensions. We will be publishing the EC10-IDC-050 version 2 datasheet soon.
Note: ECV3-10-IDC-050 with ribbon cable and IDC connector only supplied, Demo PCB not included.
Cortex 10-pin/SAM LEMTA solutions with 10 Pin target connector
Cortex 10-pin/SAM LEMTA to 10 Pin Plug-of-Nails - No Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
The TC2050-IDC-NL-050-ALL programming cable has an 0.050" pitch ribbon connector suitable for programmers and debuggers that use the Samtec FTSH-105-01 style micro-header (10-pins).
The pin connections are 1-1 and all 10 pins are connected. (The standard TC2050-IDC-NL-050 cable does not have pins 5&9 connected to be similar to our TC2050-ARM2010 adapter and may be what you need for ARM applications).
Note: The 10-pin male connectors on the Atmel-ICE have reversed (non-standard) pin numbering. For Atmel-ICE you should purchase the LEMTA version of our cables which have the 10-pin ribbon connector fitted backwards which corrects for the Atmel-ICE pin numbering reversal. (Atmel ICE comes suppplied with a ribbon cable fitted with two 10-pin IDC connectors and a 6-pin single-in-line SIP connector - The 10-pin connector at the Atmel ICE end is reversed but the other is not, correcting the pin-numbering at the target PCB. Our LEMTA cables similarly have a reversed connector).
Orientation: LEMTA - Ribbon Connector reversed for Atmel-ICE
TC2050 10 Pin “No legs” Plug-of-Nails™ to 0.050″ pitch 10 pin ribbon connector suitable for ULINK2 and similar debuggers that use the Samtec FTSH-105-01 style micro-header. As TC2050-IDC-NL-050 but with all pins connected.
This product is intended to temporarily hold a TC2050-NL cable in place on a PCB. The solution will help when board space is premium and you need to perform a hands-free programming or debugging operation. For a more robust and convenient debugging connection consider using the TC2050 legged cable and footprint. Supplied as pack of 3.
We recommend keeping a few spare of these since they are easily misplaced when working on the desktop. Over time they may lose some grip.
Cortex 10-pin/SAM LEMTA to 10 Pin Plug-of-Nails - With Legs Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
The TC2050-IDC-050-ALL programming cable has an 0.050" pitch ribbon connector suitable for ULINK2 and similar debuggers that use the Samtec FTSH-105-01 style micro-header.
The pin connections are 1-1 and all 10 pins are connected. (The standard TC2050-IDC-050 cable does not have pins 5&9 connected to be similar to our TC2050-ARM2010 adapter).
Note: The 10-pin male connectors on the Atmel-ICE have reversed (non-standard) pin numbering. For Atmel-ICE you should purchase the LEMTA version of our cables which have the 10-pin ribbon connector fitted backwards which corrects for the Atmel-ICE pin numbering reversal. (Atmel ICE comes suppplied with a ribbon cable fitted with two 10-pin IDC connectors and a 6-pin single-in-line SIP connector - The 10-pin connector at the Atmel ICE end is reversed but the other is not, correcting the pin-numbering at the target PCB. Our LEMTA cables similarly have a reversed connector).
Orientation: LEMTA - Ribbon Connector reversed for Atmel-ICE
TC2050 10 Pin “Legged ” Plug-of-Nails™ to 0.050″ pitch 10 pin ribbon connector suitable for ULINK2 and similar debuggers that use the Samtec FTSH-105-01 style micro-header. As TC2050-IDC-050 but all pins connected.
Cortex 10-pin/SAM LEMTA to 10 Pin Edge-Connect™ Debugger mating connector: 10 Pin IDC 0.05" Female (Mates with FTSH)
Edge-Connect™ - The Leading-Edge Connector!
The ECV3-10-IDC-050 is a 10-pin Edge-Connect™ connector terminated in a 10-pin 0.05" pitch female IDC. This uses version 3 of our patented literal edge of the board connector which is more robust and more convenient than previous versions. The ECV3-10-IDC-050 is suitable for ULINK2 and similar debuggers that use the Samtec FTSH-105-01 style micro-header. This cable is the equivalent to using our TC2050-ARM2010 adapter with a ECV3-10-IDC cable connected to the ULINK2’s 20-pin 0.1″ pitch traditional ARM JTAG header. The pin connections are 1-1. All 10 pins are connected.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
We generally recommend choosing the ECV3-10-IDC or EC06-IDC cables over this ECV3-10-IDC-050 because cables mating to the Cortex 10-pin 0.050″ header use very fine 0.025″ pitch ribbon cable with very few strands of tinned copper wire in each wire of the ribbon. These fine strands can break over time through flexing and stressing. The thicker ribbon cables used with our ECV3-10-IDC or ECV3-06-IDC cables have many times the cross-sectional area of copper and make for a far more robust solution.
Note: The 10-pin male connectors on the Atmel-ICE have reversed (non-standard) pin numbering. For Atmel-ICE you should purchase the LEMTA version of our cables which have the 10-pin ribbon connector fitted backwards which corrects for the Atmel-ICE pin numbering reversal. (Atmel ICE comes supplied with a ribbon cable fitted with two 10-pin IDC connectors and a 6-pin single-in-line SIP connector - The 10-pin connector at the Atmel ICE end is reversed but the other is not, correcting the pin-numbering at the target PCB. Our LEMTA cables similarly have a reversed connector).
Edge-Connect™ is the patent-pending newest member in the family of Programming Connectors and Cables from Tag-Connect.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
ECV3-10-IDC-050 has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
See below for the EC10-IDC version 1 datasheet for PCB dimensions. We will be publishing the EC10-IDC-050 version 2 datasheet soon.
Note: ECV3-10-IDC-050 with ribbon cable and IDC connector only supplied, Demo PCB not included.
Cortex 20 Pin solutions with 10 Pin target connector
Cortex 20 Pin to 10 Pin Plug-of-Nail™ - No Legs Debugger mating connector: 20 Pin IDC 0.05" Female (Mates with FTSH)
The TC2050-IDC-NL-050-ALL-20 programming cable has an 0.050" pitch ribbon connector suitable for ULINK2 and similar debuggers that use the Samtec FTSH-110-01 style micro-header. This uses the "No Legs" version of the TC2050 connector, ideally suited to production where short board connection times are required but also suitable for development.
The pin connections are 1-1 and pins 1-10 are connected, pins 11-20 are not connected in the cable.
Please refer to TC2050-IDC-NL datasheet for the PCB footprint information.
This product is intended to temporarily hold a TC2050-NL cable in place on a PCB. The solution will help when board space is premium and you need to perform a hands-free programming or debugging operation. For a more robust and convenient debugging connection consider using the TC2050 legged cable and footprint. Supplied as pack of 3.
We recommend keeping a few spare of these since they are easily misplaced when working on the desktop. Over time they may lose some grip.
Cortex 20 Pin to 10 Pin Plug-of-Nail™ - With Legs Debugger mating connector: 20 Pin IDC 0.05" Female (Mates with FTSH)
The TC2050-IDC-050-ALL-20 programming cable has an 0.050" pitch ribbon connector suitable for ULINK2 and similar debuggers that use the Samtec FTSH-110-01 style micro-header.
The pin connections are 1-1 and pins 1-10 are connected, pins 11-20 are not connected in the cable.
Please refer to TC2050-IDC datasheet for the PCB footprint information.
Cortex 20 Pin to 10 Pin Edge-Connect™ Debugger mating connector: 20 Pin IDC 0.05" Female (Mates with FTSH)
Edge-Connect™ - The Leading-Edge Connector!
This special cable has a 6-pin ECV3-10 Edge-Connect™ connector to 20-pin 0.050″ pitch ribbon connector.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
Edge-Connect™ is the patent-pending newest member in the family of Programming Connectors and Cables from Tag-Connect. ECV3-10 is the 10-pin connector.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
ECV3-06-PKT-SWD has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
New datasheet coming soon. Note that this product terminates in an 6 pin pin-strip connector.
Note: ECV3-10-050-20 with ribbon cable and Microchip PICkit 4 connector only supplied, Demo PCB not included.
Cortex 20 Pin solutions with 14 Pin target connector
Cortex 20 Pin to 14 Pin Edge-Connect™ Debugger mating connector: 20 Pin IDC 0.05" Female (Mates with FTSH)
Edge-Connect™ - The Leading-Edge Connector!
The ECV3-14-2AP-IDC is a 14-pin Edge-Connect™ connector with a 0.05" pitch ribbon cable and Cortex-20/MIPI-20 connector providing all required Cortex-20 signals including extended trace. This uses version 3 of our patented literal edge of the board connector which is more robust and more convenient. The 2AP version uses two guide pins.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
Edge-Connect™ is the patented newest member in the family of Programming Connectors and Cables from Tag-Connect.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™ so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just two tiny locating holes
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
ECV3-14-2AP-ETM has a castellation pitch of 1.27mm and requires a two tiny non-plated through holes to locate and hold the PCB in place.
Note: ECV3-14-2AP with ribbon cables and IDC connectors only supplied, Demo PCB not included.
PICkit 4 to 6 Pin Plug-of-Nails™ – No Legs (SAM) Debugger mating connector: 8 Pin 0.1" SIP strip Male
Ideal for both debugging and production programming of SAM ARM Cortex MCUs using the Microchip PICkit 4/5 or SNAP in-circuit debuggers, the 6 pin plug-of-nails™ 'no-legs' cable terminates in a 8 pin 0.1" male SIP strip for connection to the debugger. This is similar to the TC2030-PKT-NL cable but has an 8 pin SIP connector rather than 6 pin, as required when using the PICkit 4 or SNAP debugger for SAM MCU programming and/or debugging. The target board pin connections on the plug-of-nails™ connector are the same as on our TC2030-CTX-NL ARM Cortex cable.
Note: This cable is only for SWD debugging of SAM ARM Cortex MCUs. For suitable Microchip PIC cables see here.
Signal
SNAP/PICkit 4
TC2030 CTX 6-pin
TC2030-PKT-SWD Connections
NMCLR/RESET
1
3
VDD VIOREF
2
1
GND
3
5
SWO
4
6
SWCLK
5
4
SWDIO
8
2
Tag-Connect TC2030-PKT-SWD-NL cable is primarily intended for use in production programming. It is particularly suited to environments where the connection to the PCB is of short duration, and operators are working quickly from board to board.
A major advantage of the TC2030-PKT-SWD-NL is the extremely small footprint required on the PCB (hardly any bigger than a surface mount resistor) allowing the minimum possible space on your PCB to be used for the programming connection.
The TC2030-PKT-SWD-NL (no legs) cable is also compatible with the TC2030-PKT-SWD legged footprint allowing use of the TC2030-PKT-SWD legged cable for development work and TC2030-PKT-SWD-NL for fast programming in production.
This product is intended to temporarily hold a TC2030 -NL ("No Legs") cable in place on a PCB. This solution will help when board space is at a premium and you need a hands free solution for debugging. Supplied as pack of 3.
We recommend keeping a few spare of these since the tiny boards are easy to misplace when working on the bench.
For a more robust solution consider a TC2030 legged cable.
PICkit 4 to 6 Pin Plug-of-Nails™ – With Legs (SAM) Debugger mating connector: 8 Pin 0.1" SIP strip Male
Ideal for both debugging and production programming of SAM ARM Cortex MCUs using the Microchip PICkit 4/5 or SNAP in-circuit debuggers, the 6 pin plug-of-nails™ cable terminates in a 8 pin 0.1" male SIP strip for connection to the debugger. This is similar to the TC2030-PKT cable but has an 8 pin SIP connector rather than 6 pin, as required when using the PICkit 4 or SNAP debugger for SAM MCU programming and/or debugging. The target board pin connections on the plug-of-nails™ connector are the same as on our TC2030-CTX ARM Cortex cable.
Note: This cable is only for SWD debugging of SAM ARM Cortex MCUs. For suitable Microchip PIC cables see here.
Signal
SNAP/PICkit 4
TC2030 CTX 6-pin
TC2030-PKT-SWD Connections
NMCLR/RESET
1
3
VDD VIOREF
2
1
GND
3
5
SWO
4
6
SWCLK
5
4
SWDIO
8
2
Tag-Connect TC2030-PKT-SWD programming/debugging cable is primarily intended for use in development environments but is also ideal for production programming. The spring-loaded contact pins are held firmly in place by four plastic legs each of which clips securely into its own locating hole.
Tag-Connect TC2030-PKT-SWD is ideal where you need to maintain a connection to the PCB for an extended period such as when performing testing or development work.
See also TC2030-PKT-SWD-NL for applications where an even smaller footprint is required.
PICkit 4 to 6 Pin Edge-Connect™ (SAM) Debugger mating connector: 8 Pin 0.1" SIP strip Male
Edge-Connect™ - The Leading-Edge Connector!
This special cable has a 6-pin ECV3-06 Edge-Connect™ connector for use with Microchip PICkit 4.
ECV3 is the third generation in the Edge-Connect™ family. ECV3 is NOT compatible with the previous Edge-Connect family and both will continue to be supported as current products into the future.
ECV3 makes some minor improvements adding greater robustness, improved convenience and is designed to be a mainstream product.
Edge-Connect™ is the patent-pending newest member in the family of Programming Connectors and Cables from Tag-Connect. ECV3-06 is the 6-pin connector.
By connecting to the literal edge of the PCB (not the surface near the edge like traditional edge-connectors) Edge-Connect™ is designed to essentially eliminate the wasted real-estate needed by JTAG programming and test connectors.
Edge-Connect™ is an Ideal solution for space-sensitive PCB’s and modules that don’t have room on the board for traditional connectors but which still need a means of programming firmware and testing.
We've designed Edge-Connect™so that we can offer low-cost, fast-turn, customized connector solutions to meet the unique requirements of your PCB - Contact Us if you have a custom requirement.
Connects directly to the literal edge of the PCB
PCB snaps directly onto the Edge-Connect™
Zero Component Cost on the PCB
Maximizes available PCB real-estate
Eliminates the cost of a connector on every board
Requires just one tiny locating hole
Low profile edge access ideal for use with stacked PCB’s with no access headroom
Cant be connected backwards due to keyed feature
Standard or custom design configurations available
Alternative pitch? Three castellated edges? No problem!
No Header! - No Brainer!
Instead of using the usual space-costly Surface Mount or Plated Through-Hole connectors, Edge-Connect™ has springy gold-plated contacts that connect directly to the literal edge of the target PCB using edge castellation.
A Castellated PCB edge is a board edge that has plated through holes that are placed overhanging the edge of the board and typically made at little to no extra cost even from most cheap proto-board fab services (often a check box in the online quote is marked "Castellated Holes").
Castellated edges are commonly used on RF, WiFi, BLE and IoT sensor modules making them suitable for soldering as an SMT component onto host PCB’s using the castellated holes as pins. Edge-Connect™ allows test and programming and even debugging without first soldering the module to the host PCB. This makes it very useful for factory test and programming of the module.
ECV3-06-PKT-SWD has a castellation pitch of 1.27mm and requires a single tiny non-plated through hole to locate and hold the PCB in place.
New datasheet coming soon. Note that this product terminates in an 6 pin pin-strip connector.
Note: ECV3-06-PKT-SWD with ribbon cable and Microchip PICkit 4 connector only supplied, Demo PCB not included.
1 x TC2030-IDC-NL
1 x TC2030-CTX-NL 6-Pin "No Legs" Cable with 10-pin micro-connector for Cortex processors
1 x ECV3-06-CTX 6-pin Castellated Board-Edge Connector for ARM Cortex
1 x TC2030-CTX 6-Pin Cable for ARM Cortex
1 x TC2030-CTX-ETM
1 x ECV3-10-IDC-050 10-pin Castellated Board-Edge Connector to 10-pin 0.05" IDC
